Cisco Catalyst 2960-X Series Switches are the next generation of the world's most widely deployed access switches, providing Layer 2 and Layer 3 access features. The switches deliver best-in-class energy efficiency, while preserving your investments through mixed stacking with existing Catalyst 2960-S and SF switches.
|WS-C2960X-48LPD-L Specification and Datasheet|
|10/100/1000 Ethernet Ports||48|
|Uplink Interfaces||2 SFP+|
|Cisco IOS Software Image||LAN Base|
|Available PoE Power||370W|
|LAN Base Scalability Numbers|
|Unicast MAC Addresses||16K|
|IPv4 Unicast Direct Routes||2K|
|IPv4 Unicast Indirect Routes||1K|
|IPv6 Unicast Direct Routes||2K|
|IPv6 Unicast Indirect Routes||1K|
|IPv4 Multicast Routes and IGMP Groups||1K|
|IPv6 Multicast Groups||1K|
|IPv4 QoS ACEs||500|
|IPv6 QoS ACEs||500|
|IPv4 Security ACEs||625|
|IPv6 Security ACEs||625|
|FlexStack Plus Scalability and Performance|
|2960-XLAN Base||Stack Bandwidth: 80G
Stack Limit: 8
Cisco IOS Feature Set: IOS LAN Base
|2960-X LAN Base mixed with
2960-S/SF LAN Base
|Stack Bandwidth: 40G
Stack Limit: 4
Cisco IOS Feature Set: IOS LAN Base
|PoE and PoE+ Power Capacity|
|Maximum Number of PoE+ (IEEE 802.3at) Ports||12 ports up to 30W|
|Maximum Number of PoE (IEEE 802.3af) Ports||24 ports up to 15.4W|
|Available PoE Power (Single PS Source)||370W|
|Flash memory||128 MB for LAN Base & IP Lite SKUs, 64 MB for LAN Lite SKUs|
|DRAM||512 MB for LAN Base and 256 MB for LAN Lite|
|CPU||APM86392 600MHz dual core|
|Console Ports||USB (Type-B), Ethernet (RJ-45)|
|Storage Interface||USB (Type-A) for external flash storage|
|Network Management Interface||10/100 Mbps Ethernet (RJ-45)|
|Performance and Scalability|
|Forwarding bandwidth||108 Gbps|
|Switching bandwidth||216 Gbps|
|Maximum active VLANs||1023|
|VLAN IDs available||4096|
|Maximum transmission unit (MTU)-L3 packet||9198 bytes|
|Jumbo frame - Ethernet frame||9216 bytes|
|Forwarding Rate||130.9 Mpps, 64-Byte L3 Packets|
|Dimensions (H x W x D)|
|Inches||1.75 x 14.5 x 17.5|
|Centimeters||4.5 x 36.8 x 44.5|
|Operating temperature up to 5000 ft (1500 m)||Fahrenheit: 23º to 113ºF; Centigrade: -5º to 45ºC|
|Operating temperature up to 10,000 ft (3000 m)||Fahrenheit: 23º to 104ºF; Centigrade: -5º to 40ºC|
|Short-term exception at sea level||Fahrenheit: 23º to 131ºF; Centigrade: -5º to 55ºC|
|Short-term exception up to 5000 feet (1500 m)||Fahrenheit: 23º to 122ºF; Centigrade: -5º to 50ºC|
|Short-term exception up to 10,000 feet (3000 m)||Fahrenheit: 23º to 113ºF; Centigrade: -5º to 45ºC|
|Short-term exception up to 13,000 feet (4000 m)||Fahrenheit: 23º to 104ºF; Centigrade: -5º to 40ºC|
|Storage temperature up to 15,000 feet (4573 m)||Fahrenheit: 23º to 158ºF; Centigrade: -25º to 70ºC|
|Operating altitude||Feet: Up to 10,000; Meters: Up to 3,000|
|Storage altitude||Feet: Up to 13,000; Meters: Up to 4,000|
|Operating relative humidity||10% to 95% noncondensing|
|Storage relative humidity||10% to 95% noncondensing|
|Measured per ISO 7779 and declared per ISO 9296.
Bystander positions operating mode at 25°C ambient.
Sound Pressure, Dba:
LpAm(Typical): 39dB; LpAD(Maximum): 43 dB
Sound Power, dbA:
LwA(Typical): 4.9 B LwAD (Maximum): 5.3 B
|MTBF in hours||277,960|
|Connectors and Interfaces|
|Ethernet Interfaces||10BASE-T ports: RJ-45 connectors, 2-pair Category 3, 4, or 5 unshielded twisted-pair (UTP) cabling
100BASE-TX ports: RJ-45 connectors, 2-pair Category 5 UTP cabling
1000BASE-T ports: RJ-45 connectors, 4-pair Category 5 UTP cabling
1000BASE-T SFP-based ports: RJ-45 connectors, 4-pair Category 5 UTP cabling
|SFP Interfaces||GLC-LH-SMD GLC-SX-MMD
GLC-EX-SMD (CPN 10-2624-01 or later only)
|SFP+ Interfaces||SFP-10G-LR SFP-10G-SR
DWDM SFP+ SFP-H10GB-CU1-5M
|Indicator LEDs||Per-port status: Link integrity, disabled, activity, speed, and full duplex
System status: System, RPS, Stack link status, link duplex, PoE, and link speed
|Cisco Catalyst 2960-XFlexStack-Plus stacking cables||CAB-STK-E-0.5M FlexStack-Plus stacking cable with a 0.5 m length
CAB-STK-E-1M FlexStack-Plus stacking cable with a 1.0 m length
CAB-STK-E-3M FlexStack-Plus stacking cable with a 3.0 m length
|Cisco Catalyst 2960-X console cables||CAB-CONSOLE-RJ45 Console cable 6 ft. with RJ-45
CAB-CONSOLE-USB Console cable 6 ft. with USB Type A and mini-B connectors
|Power||The internal power supply is an auto-ranging unit and supports input voltages between 100 and 240V AC
Use the supplied AC power cord to connect the AC power connector to an AC power outlet
The Cisco RPS connector offers connection for an optional Cisco RPS 2300 that uses AC input and supplies DC output to the switch
Only the Cisco RPS 2300 (model PWR-RPS2300) should be attached to the redundant-power-system receptacle
|Voltage and Power Ratings|
|Input Voltage (Auto ranging)||100 to 240 VAC|
|Input Current (Amperes)||5A-2A|
|Frequency||50 to 60Hz|
|Power Rating (Switch maximum consumption values)||0.48kVA|
|DC Input Voltages (RPS Input)||4A at 12V; 8A at 53V|
|Management and Standards Support|
UDP-MIB ePM MIB
|Standards||IEEE 802.1D Spanning Tree Protocol
IEEE 802.1p CoS Prioritization
IEEE 802.1Q VLAN
IEEE 802.1ab (LLDP)
IEEE 802.3af and IEEE 802.3at
IEEE 802.3ah (100BASE-X single/multimode fiber only)
IEEE 802.3x full duplex on 10BASE-T, 100BASE-TX, and 1000BASE-T ports
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.3ab 1000BASE-T
IEEE 802.3z 1000BASE-X
RMON I and II standards
SNMP v1, v2c, and v3
IEEE 802.3ae 10Gigabit Ethernet
|RFC compliance||RFC 768 - UDP
RFC 783 - TFTP
RFC 791 - IP
RFC 792 - ICMP
RFC 793 - TCP
RFC 826 - ARP
RFC 854 - Telnet
RFC 959 - FTP
RFC 951 - Bootstrap Protocol (BOOTP)
RFC 1112 - IP Multicast and IGMP
RFC 1157 - SNMP v1
RFC 1166 - IP Addresses
RFC 1256 - Internet Control Message Protocol(ICMP) Router Discovery
RFC 1305 - NTP
RFC 1492 - TACACS+
RFC 1493 - Bridge MIB
RFC 1542 - BOOTP extensions
RFC 1643 - Ethernet Interface MIB
RFC 1757 - RMON
RFC 1901 - SNMP v2C
RFC 1902-1907 - SNMP v2
RFC 1981 - Maximum Transmission Unit (MTU) Path Discovery IPv6
FRC 2068 - HTTP
RFC 2131 - DHCP
RFC 2138 - RADIUS
RFC 2233 - IF MIB v3
RFC 2373 - IPv6 Aggregatable Addrs
RFC 2460 - IPv6
RFC 2461 - IPv6 Neighbor Discovery
RFC 2462 - IPv6 Autoconfiguration
RFC 2463 - ICMP IPv6
RFC 2474 - Differentiated Services (DiffServ) Precedence
RFC 2597 - Assured Forwarding
RFC 2598 - Expedited Forwarding
RFC 2571 - SNMP Management
RFC 3046 - DHCP Relay Agent Information Option
RFC 3376 - IGMP v3
RFC 3580 - 802.1X RADIUS
Please refer to below table:
|Switch Model||Maximum Number of PoE+ (IEEE 802.3at) Ports||Maximum Number of PoE (IEEE 802.3af) Ports||Available PoE Power (Single PS Source)|
|Cisco Catalyst 2960X-48FPD-L||24 ports up to 30W||48 ports up to 15.4W||740W|
|Cisco Catalyst WS-C2960X-48LPD-L||12 ports up to 30W||24 ports up to 15.4W||370W|
WS-C2960X-48LPD-L with 2 10G SFP+ uplink while WS-C2960X-48LPS-L uplink is 4GE SFP.
No, WS-C2960X-48LPD-L only available as LAN Base.
Please refer the below list
|Uplink Interfaces||Cisco IOS Software Image||Available PoE Power||FlexStack-Plus Capability|
|Cisco Catalyst 2960X-48FPD-L||48||2 SFP+||LAN Base||740W||Y|
|Cisco Catalyst 2960X-48LPD-L||48||2 SFP+||LAN Base||370W||Y|
|Cisco Catalyst 2960X-24PD-L||24||2 SFP+||LAN Base||370W||Y|
|Cisco Catalyst 2960X-48TD-L||48||2 SFP+||LAN Base||-||Y|
|Cisco Catalyst 2960X-24TD-L||24||2 SFP+||LAN Base||-||Y|
|Cisco Catalyst 2960X-48FPS-L||48||4 SFP||LAN Base||740W||Y|
|Cisco Catalyst 2960X-48LPS-L||48||4 SFP||LAN Base||370W||Y|
|Cisco Catalyst 2960X-24PS-L||24||4 SFP||LAN Base||370W||Y|
|Cisco Catalyst 2960X-24PSQ-L||24 (8PoE)||2 SFP, 2 10/100/1000BT||LAN Base||110W||-|
|Cisco Catalyst 2960X-48TS-L||48||4 SFP||LAN Base||-||Y|
|Cisco Catalyst 2960X-24TS-L||24||4 SFP||LAN Base||-||Y|
|Cisco Catalyst 2960X-48TS-LL||48||2 SFP||LAN Lite||-||-|
|Cisco Catalyst 2960X-24TS-LL||24||2 SFP||LAN Lite||-||-|
Switches supporting Power over Ethernet Plus (PoE+) can supply power to any IEEE 802.3af or IEEE 802.3at compliant end device. PoE+ removes the need for wall power to each PoE+ enabled device and eliminates the cost for additional electrical cabling that would otherwise be necessary in IP phone and wireless LAN deployments. PoE switches also eliminate the need for power injectors and PoE midspans for powering IP devices. The list of devices that require more than the 15.4W provided by 802.3at is growing. Devices currently requiring more than 15.4W of PoE power include Cisco video IP phones and IP video cameras. Additional devices requiring more than 15.4W of power are coming.
WS-C2960X-48LPD-L supports both the PoE and PoE+ standards and can classify a powered device as either Type 1 or 2 with a one-event classification. A Type 2 powered device supports Class 4 in order to obtain more power than is supported by the legacy power levels (30W). A Type 1 powered device can support only up to Class 3, or 15.4W.
No. Two-event classification is specific to mid spans that work on power-supplying equipment (PSE). The Cisco Catalyst 2960-X Series supports only one-event classification.
Yes, the Cisco Catalyst 2960-X Series Switches can optionally detect the powered device power classification signature and budget the appropriate power. This reduces the maximum power that must be budgeted by the switch and provisioned in the wiring closet.
The Cisco Catalyst 2960-X Series supports both PoE standards, 802.3af and 802.3at, which define the maximum power that can be supplied to a port. The switches can provide up to 30W per port.
Yes, list as below:
GLC-EX-SMD (CPN 10-2624-01 or later only)
List as below:
Yes, you can use a 3rd party transceiver, however switch will generate warning, 3Anetwork recommend customers using original Cisco transceiver.
If you need downlink 100M switches, refer to Part A.
If you need downlink 1000M switches, refer to Part B.
We ship Cisco networking products to worldwide. Normally cargo will be shipped within 2 business days after payment arrived. Tracking Number will be offered once delivery done.
|The following is a list of delivery options and estimated delivery time which 3Anetwork.com offers:|
|Delivery Options||Estimated Delivery Time|
|DHL||2-4 business days|
|Fedex||2-4 business days|
|HongKong EMS||5-10 business days|
|HongKong Air Parcel||10-20 business days|
|By sea||10-20 business days|
Above mentioned information are just for your reference only, we will keep you posted for the tracking delivery schedule. 3Anetwork.com is responsible for transporting goods to port. All subsequent customs fees are the responsibility of the buyer. 3Anetwork.com will recommend trustworthy freight forwarders to you.
|Paypal||Master Card||Visa||Discover||JCB||American Express||eChek||Wire Trans fer||Western Union|
100% Low Price Guarantee3Anetwork.com provides high-quality products at low wholesale prices.
All items are ORIGINAL and GENUINE onlyItem conditions are all "New Sealed".
100% Money Back GuaranteeYou can contact our customer service team to exchange or return any product that you bought from us.
Free CCIE Technical SupportOur FREE Cisco CCIE Expert Consultancy Support is over the phone, by chat, by email or by login remotely.
Flexible Secure Payment & ShipmentVerified authorization: Mcafee Secure, VeriSign Secured .
The Support Contact:
If your Cisco products failed, you must contact your sales representative to verify product failure. If the problem still can't be fixed by remote support methods i.e. email or phone support, you may start the RMA procedure.
The RMA Confirmation:
Your sales representative will send you RMA form.
(We will need PO No.; Product Serial No.; Description of Failure or Problem)
You Fill it and send back to sales representative.
RMA Return Shipment:
A: After receive your RMA form, sales representative will send you return instruction by email, including shipping address and special shipping invoice.
B: Returned products have to be packed properly to avoid damage during delivery.
C: All accessories and user documentations should be returned.
D: Once shipped, pleases avail sales representative tracking No. immediately.
The Customer is responsible for paying shipment charges when returning to us; we will pay for shipment of the repaired items back to the customer.
RMA Turnaround Time:
The defective products will be sent for repair.
Within four weeks after receipt of returned item, the repaired or replacement item will be ready for return shipment.
Then item will be shipped to customer by Express such as DHL.
3Anetwork.com wholesales Cisco Catalyst 2960 switch WS-C2960X-48LPD-L, 2960X-48LPD-L, 2960X-48LPD, original new Cisco WS-C2960X-48LPD-L at competitive price. In most cases, we can deliver WS-C2960X-48LPD-L in 2 business days. Simply add to your shopping cart for the best price. Good discount of Cisco 2960 switch, best Cisco Catalyst 2960 switch WS-C2960X-48LPD-L price, save your money.
3Anetwork.com, the global leading Cisco networking products wholesaler, sell original new Cisco Catalyst 2960 switch, Cisco 2960 switch WS-C2960X-48LPD-L, 2960X-48LPD-L, 2960X-48LPD, Catalyst 2960-X 48 GigE PoE 370W, 2 x 10G SFP+ LAN Base, ship WS-C2960X-48LPD-L to worldwide.
Tell us what you think about WS-C2960X-48LPD-L, share your opinion! Make sure that your review focus on WS-C2960X-48LPD-L. Reviews will be reviewed and moderated in short time. Inappropriate reviews will not be posted.
Have any question or inquire for WS-C2960X-48LPD-L ? Please Contact Us.